Any questions?
+420 603 357 606
0
Total : 0 €
0 € without VAT
Go to Cart

Product description

According to your predesign we can produce a bilateral stamping dies for a dry impress to a paper. These stamping dies will we put into handheld lever stamping dies for a quick and immediate application to any document. The stamping die is circular and you can use its whole area with a diameter of 40 mm for realizing your graphical ideas and to which a 2D predesign will be elegenter engraved. Dry impress is a three-dimensional security printing item used for a prevention from falsification. It is an uncopyable and an untransferable identification of documents on the basis of a three-dimensional motive that is visible from both facial and inner side of a printed matter. More about the technique of this dry impress can be found under these sample pictures.

Allow us to present you these two very imporatnt facts that differ our 3D seals from the compretitory products just before presenting you the technique used by a relief seal:

    I.       Most of the time, 3D stamping dies production is offered in plastics and the reason why is the price. Plastics offer a variety of a cheap and a quick treatment and it seems that the price vs. the output proportion is great. However, in our opinion, plastics does not fulfil any basic requirements for a quality and stamping dies get quite quickly worn out. The intended effect of glamorizing and making it luxurious is gradually degraded. Plastic seal is possible to use in a long term only for papers with a small self-weight, when creating relief imprints to a thick paper or other materials (lether), it enormly increases the pressure to stamping decks and a rapid stamping areas detrition follows. In short, the plastics stays faithful to the characteristics given by its name and particular contours start to „turn aside“ under repeated pressure exposal. Because of this we offer only steel plastic types which longevity is almost unlimited and they allow the impress into arbitrary self-weight papers, the leather or even into very thin aluminic tinplates. Somewhere among plastic and steel stamping dies there are quantitatively similar stamping dies made of magnesium or a brass. A plastic type made of steel however, shows the best parameters...

    II.       Not all relief seals producers know how to put your concrete graphical vision including your special graphical symbols onto the stamping die. They engrave you only a specific chain of signs. We put onto your die any graphical motive just as it will be vectorally described in a folder sent by you (Corel CDR) or we can create vectoral patterns according to your ideas from individual graphical components given to us. The only limiting parameter is diversity that is, naturally, limited because the impress needs to have a given depth.

The dry impress technique has not too many technologically different variatins and can therefore be named by many synonyms. Among the most common used belongs blind impress, dry impress and other collocations directly expressing the technical procedure: embossing, relief impress, plastic sign, plastic water sign etc. Blind impress is therefore a technique useing an impress without colour, impressing the stamping die into the paper or an eventually different material with a suitable width.


Blind impress appears to be a very interesting alternative of securing the documents and marking the charts because its imitation is very hard. It is not possible to reliefly scan the imprint and it cannot be practically ripped off by e.g. ironing. Comparing to other security self-adhesive labels with holographic patterns, there are 4 essential adavantages of a blind impress:


1.    Handheld lever stamping dies impress a seal to any paper practically without limitation of applications amount. It cannot happan that the labels run out as in case of holographic security labels.


2.    Even the most clever falsificator will not be able to move (ustick, cut out etc) the blind impress from one document to another because that is simply not possible.


3.    Dry impress dose not use a colour and it does not change the colour of a document in a place of impress after application. Thanks to this, it does not interfere with a graphical composition of the document.


4.    In connection to the advantage number 3 mentioned above, it is very desirable for the impress not to disturb the labeled product. We can use the blind impress or a water mark. The measure of visibility of the impress is highly controlled by the pressure you put on the lever when applying the blind impress. The lower pressure the less disturbing will the 3D element be. At the same time, it will still be greatly visible.


Dry impress is therefore a securing item of a document preventing it from falsification. It uses a technology production of a 3D picture of a graphical logo and a text by a relief impress – impressing the engraved stamping die opposite its dissymetrical incavated counterpart through the document that should be labeled. The imprint can be created into papers of different self-weigth – using very thin or very thick printing materials will require finding suitable strength for the stamping die lever.


The predesign of a stamping die look is practically no different to a predesign of a single layered hologram. Graphical pattern needs to be sent in vectoral form and on its basis both stampng dies will be engraved onto the plastic steel imprint. You will get those deposited in precise lever impress mechanism later.

Choosing and rotating the stamping die
Both top and bottom (positive and inverse) part of a die can be easily demonted from a lever impress, rotate as needed and put back together. This option can be used mostly for setting the printing to a top or a bottom edge of the documents according to your documents’ requirements. It can also deal with a case when you need to seal something into the middle of the right or the left edge of the page.
 
Embossing direction bottom up, top down, left to right, right to left
Weight 0.8927 kg

Maintenance of steel stamp - document .pdf download here

Choosing and rotating the stamping die R1

Both top and bottom (positive and inverse) part of a die can be easily demonted from a lever impress, rotate as needed and put back together. This option can be used mostly for setting the printing to a top or a bottom edge of the documents according to your documents’ requirements. It can also deal with a case when you need to seal something into the middle of the right or the left edge of the page.

Related products

R1 Steel embossing plates

Variant :
Choose dimensions (mm):
width x height
Embossing direction
Amount:
Total price
205
166.667 € without VAT
Upload your design:
I don't have my own graphic design, I want to create it from you (please provide details in the note).
Note: